Unified Lanshop Owners Portal

Sir baka parepareho ng computername yan. Ang dating sakin kasi parang cloned yung mga pc mo kaya parepareho ng settings.

@johwi

hindi po sir. bale yung Server ko po ay SERVER1 SERVER2 ang name

yung workstations PC1 PC2 & so on..

pag automatic IP & DNS. nagkakakitaan yang PC1 & PC2 pero di ma-aaccess. ang na-aaccess lang nila e yung 2 Server.
pag manual IP & DNS. di na sila nagkakakitaan. Servesr lang nakikita nila.

ok ganito na lang gawin mo. Palitan mo sila lahat ng workgroup name. wag ung dati mo na nagamit...as in bago. isa isahin mo. Then make sure ung firewall ng windows naka off.

@bryiee

may password ba yung di mo ma-acces? kung blank ang password, talagang di mo ma-acces yan.

@bryiee
Vista ka nga pala no?


Network discovery may beblocking you from seeing other computers and devices. To turn on th network discovery setting, follow these steps:

1. Open Network and Sharing Center by clicking the Start button , clicking Control Panel, clicking Network and Internet, and then clicking Network and Sharing Center.

2. If network discovery is off, click the arrow button to expand the section, click Turn on network discovery, and then click Apply. If you are prompted for an administrator password or confirmation, type the password or provide confirmation.

you can further review using this:
technet.microsoft.com/en-us/library/bb727037.aspx

johwi wrote:
ok ganito na lang gawin mo. Palitan mo sila lahat ng workgroup name. wag ung dati mo na nagamit...as in bago. isa isahin mo. Then make sure ung firewall ng windows naka off.

bale kasama po yung servers sir? currently po yung default po na WORKGROUP ang gamit kong Name..

dmateo wrote:
@bryiee

may password ba yung di mo ma-acces? kung blank ang password, talagang di mo ma-acces yan.

nope. wala pong pw ang mga workgroup computers ko. maski po yung password protected po sa Network & Sharing naka off.

problem ko po pag click ko yung Workstation Number gamit ang isa pang Workstation. ayaw niya po ma open.

johwi wrote:
@bryiee
Vista ka nga pala no?


Network discovery may beblocking you from seeing other computers and devices. To turn on th network discovery setting, follow these steps:

1. Open Network and Sharing Center by clicking the Start button , clicking Control Panel, clicking Network and Internet, and then clicking Network and Sharing Center.

2. If network discovery is off, click the arrow button to expand the section, click Turn on network discovery, and then click Apply. If you are prompted for an administrator password or confirmation, type the password or provide confirmation.

you can further review using this:
technet.microsoft.com/en-us/library/bb727037.aspx

opo sir. naka network discovery ON po ang lahat.

@johwi

iniba ko na yung workgroup name ng lahat ng PC sir.

same parin po ang nangyayare sir :(

pano ba mag configure ng DNS? kasi pag click ko diagnose may sinasabi about DNS e..

ginawa ko Automatic lahat. same ang nangyayare. nakikita at naaccess nila servers. pero pag workstation to workstation nakikita din pero hindi ma-access

pag manual naman yung IP address ganito settings ko

IP Address: 192.168.1.10X (1 & 2 Server 3 & So on.. Workstations)
Subnet Mask: 255.255.255.0
Default Gateway: 192.168.1.1

Use the Following DNS Addresses:
Prefered DNS: 192.168.1.1

tama po ba ?

bryiee wrote:
@johwi

iniba ko na yung workgroup name ng lahat ng PC sir.

same parin po ang nangyayare sir :(

pano ba mag configure ng DNS? kasi pag click ko diagnose may sinasabi about DNS e..

ginawa ko Automatic lahat. same ang nangyayare. nakikita at naaccess nila servers. pero pag workstation to workstation nakikita din pero hindi ma-access

pag manual naman yung IP address ganito settings ko

IP Address: 192.168.1.10X (1 & 2 Server 3 & So on.. Workstations)
Subnet Mask: 255.255.255.0
Default Gateway: 192.168.1.1

Use the Following DNS Addresses:
Prefered DNS: 192.168.1.1

tama po ba ?

up!!